7/8″ x 150′ Seven Eigths Inch Roll Solid Prem Accent stripe in many colors
Specifications
| Return Shipping Will Be Paid By | Buyer |
| Returns Accepted | Returns Accepted |
| Item Must Be Returned Within | 30 Days |
| Refund Will Be Given As | Money Back |
| Size | 7/8" x 150' |
| Manufacturer Part Number | 0007 |
| Country/Region Of Manufacture | United States |
| Placement On Vehicle | Left |
| Brand | Universal Products Inc |
| Theme | Graphic |
Up for “Buy It Now” is a Seven Eights Inch (7/8") Roll of Solid Stripe 150 feet long. This box includes a 150-foot roll of stripe made from 2mil high performance automotive vinyl. This is high performance cast PVC film with a permanent, acrylic, pressure-sensitive adhesive. Designed for superior quality exterior graphics for the automotive, signage, and commercial industries. • Film: 2.0-mil premium cast vinyl with clear, acrylic, permanent, pressure-sensitive adhesive. • Liner: 78# white kraft. • Exterior Durability: 9 years*. Use to customize and accent your vehicle or boat. I also have 3mil stripe listed on ebay. This is a superior material. This is the same vinyl as the pinstripe I have listed. This stripe has a clear overtape to be removed after applying. If you dont see it in the drop down menu and see it avial here, them please contact seller to see if it's available. type colors.lendaproducts.com to see colors If you dont see it Please “send a note” or use “contact seller” to specify color. Avail in most colors shown but not all. Recommended Application Instructions All surfaces are contaminated to some degree. To ensure good adhesion to any vehicle surface it is critical that you follow these recommended procedures in decontaminating and preparing the surface prior to any vinyl product installation. Note: A clean, lint free towel or cloth must be used between each of the cleaning steps. Cleaning Procedures: Remove heavy road grime or tar by using a solvent, such as acetone, zylene, or kerosene, on a clean, lint free towel. (Please note that repeated use of solvents may cause damage to painted surfaces. Prior to using any solvent, apply to an area on the vehicle to test for negative reaction.) When a silicone substance or residue is suspected, wash and rinse the contaminated area with liquid dish detergent and warm water. Then dry the surface with a clean, lint free towel or cloth. After using the solvent and/or detergent wash, use a clean, lint-free towel or cloth. Finish up the cleaning process by wiping down the entire area with Isopropyl Alcohol. To avoid recontamination during the final cleaning step, wipe the surface in just one direction, using a clean, lint-free towel or cloth. Temperature Recommendations: Universal Products recommends the temperature be between 60 and 80 degrees at the time of installation. We also discourage any installation when temperatures are above 90 degrees and below 50 degrees. Surface temperatures should be brought to within the 50 and 90 degree range before attempting installation. Application Procedures: A squeegee should be used to install graphics and striping. Because vinyl is a pressure-sensitive product it is imperative to squeegee a second time after the premask is removed. After the premask is removed, a protective sleeve or towel should be placed over the squeegee to protect the striping and graphics. Please note when removing premask/application tape, always pull it slowly and back onto itself at a 180-degree angle. A sharp air release tool or pin should be used to pierce the outer edge of any remaining trapped air bubbles. Using a knife or blade to release the air will result in a cut rather than a puncture in the vinyl. The cutting or trimming of any stripe or graphic should be done with the sharpest knife possible. Any openings, such as doors should be trimmed back away from edges at least 1/8 of an inch. (Please note when burying one stripe under another stripe such as in a pinstripe, you must overlap the bottom stripe with the top stripe by at least 1/4 of an inch). Check out my other items for sale.
Related Items
